Jump to: navigation, search

max-time-deviation

Section: gim-etl
Default Value: 30
Valid Values: 1-120
Changes Take Effect: On the next ETL cycle
Dependencies: None
Modified: 8.5.015.19 (scope extended); 8.1.4 (minimum valid value changed)

Specifies the maximum time deviation, in seconds, to take into account for time synchronization inaccuracy between host system clocks. Starting with release 8.5.015.19, this option also specifies the maximum acceptable delay the transformation job will accommodate in scenarios in which ICON creates delayed records in the GM_F_USERDATA table in IDB.

If the maximum time deviation or delay is exceeded, Genesys Info Mart results become unreliable.

extract-data-stuck-threshold

Section: gim-etl
Default Value: 28860
Valid Values: Any integer equal to or greater than 1800
Changes Take Effect: On the next ETL cycle
Dependencies: None

Specifies the time, in seconds, that Genesys Info Mart waits for stuck data to become available in IDB. For example, if new data is available until 3:00 PM and the value for extract-data-stuck-threshold is set to 28860 (8 hrs 1 min.), Genesys Info Mart extracts data that has a timestamp from 6:59 AM to 3:00 PM. IDB data from the time intervals before 6:59 AM is not, and will never be, extracted.

Enabling High Availability

The following steps summarize the task flow to enable Genesys Info Mart to provide high availability (HA) of reporting data in a new or existing deployment.

  1. Provide redundancy for monitoring the data sources and storing source data.

    Create and configure identical redundant ICON Applications for the type of details you require. For more information, see Configuring ICON.

    Except for identical configuration, there are no special requirements for HA ICON applications. However, especially ensure the following:

    • On the Connections tab of every ICON Application object, an ADDP connection has been configured to every data source that the ICON instance might be required to monitor. The connection list can include HA pairs of Configuration Servers, T-Servers, Interaction Servers, or Outbound Contact Servers.

      Remember that you configure an overt connection only to the primary data source.

      For example, say the deployment consists of:

      • An HA pair of Configuration Servers (primary Configuration Server 1 and backup Configuration Server 1a)
      • Two HA pairs of T-Servers (primary T-Server 1, backup T-Server 1a, primary T-Server 2, and backup T-Server 2a)
      • A single set of redundant ICONs for Configuration and Voice details (ICON-1 and ICON-2, storing data in IDB-1 and IDB2, respectively)

      Then both ICON-1 and ICON-2 must have connections to Configuration Server 1, T-Server 1, and T-Server 2.

    • On the General tab of every data-source application whose availability and activity Genesys Info Mart must monitor, the State Enabled check box is selected.
    • On the General tab of every ICON in the Genesys Info Mart Application connections that Genesys Info Mart must monitor, the State Enabled check box is selected.
    • The value of the dss-no-data-tout option (see Important [callconcentrator] ICON Configuration Options) is suitable for your HA deployment; the default value is 5 minutes.
    Tip
    If you need to restart existing ICON application(s) for configuration information to take effect, Genesys recommends that you do not restart ICON at this time; see step 5.

  2. Provide redundancy for the Genesys Info Mart database sources (the IDBs).

    Create and initialize identical redundant IDBs, together with their associated DAPs, to store the type of ICON details that you require.

    For more information about how to prepare an IDB, see Preparing IDBs to work with Genesys Info Mart.

    For more information about how to configure a DAP for Interaction Concentrator, see the Interaction Concentrator Deployment Guide for your release.


  3. Provide redundancy for Genesys Info Mart to access the redundant IDBs.

    Configure identical redundant DAPs to enable the Genesys Info Mart Server to access the redundant IDBs. Create a separate DAP to enable access to each redundant IDB.

    Ensure that all these extraction DAPs are enabled (the State Enabled check box on the General tab of the DAP application object is selected).

    For more information about how to configure the required DAPs, see Preparing Extraction DAPs.


  4. Configure the Genesys Info Mart Server application.

    Configure the Genesys Info Mart Application object in the usual way. For more information, see Configuring the Genesys Info Mart Application.

    There are no special requirements for the Genesys Info Mart Server application in an HA environment. However, especially ensure the following:

    • On the Connections tab of the Genesys Info Mart Application object, a connection has been configured to every redundant ICON Application in the deployment.
    • On the Connections tab of the Genesys Info Mart Application object, a connection has been configured to every DAP that provides access to a redundant IDB in the deployment.
    • The values of the following options are suitable for your HA deployment:

  5. Start or, if necessary, restart the ICON applications.
    For more information about how to start ICON, see the Interaction Concentrator Deployment Guide for your release. Also see the ICON documentation for information about when you might need to restart an existing ICON.
  6. In a new deployment, start the Genesys Info Mart Server.
    For more information about how to start Genesys Info Mart, including information about modifying startup parameters, see Starting and Stopping Genesys Info Mart Server.
    Tip
    The Genesys Info Mart Server supports dynamic changes. If you are adding HA to an existing deployment, it is not necessary to interrupt the Genesys Info Mart job schedule or to stop Genesys Info Mart for new connection information or other configuration option changes to take effect.

  7. Verify the deployment.
    Review logs to confirm the results of the configuration check, to verify connections to all redundant Interaction Concentrator instances and data sources, and to verify correct configuration.

This page was last edited on October 5, 2018, at 15:49.
Comments or questions about this documentation? Contact us for support!