Jump to: navigation, search

Configuring Cisco Media Gateway

This page provides an overview of the main steps that are required in order to configure Cisco Media Gateway.

Integrating with Cisco Media Gateway

Verify that Cisco Media Gateway is working

Verify that Cisco Media Gateway is functional and handling calls appropriately.

The procedures in this topic assume that Cisco Media Gateway is functional and handling calls appropriately. For more information, see Cisco Media Gateway-specific documentation.

Configuring an E1 environment

Purpose

To configure an E1 environment. This section provides an example of an E1 configuration.

Start

  1. Configure a controller:
    controller E1 0/2/0
    framing NO-CRC4
    ds0-group 0 timeslots 1 type fxo-loop-start
    ds0-group 1 timeslots 2 type fxo-loop-start
    ds0-group 2 timeslots 3 type fxo-loop-start
  2. Configure voice ports:
    voice-port 0/2/0:0
    output attenuation 0
    station-id name 2300090
    voice-port 0/2/0:1
    output attenuation 0
    station-id name 2300091
    voice-port 0/2/0:2
    output attenuation 0
    station-id name 2300092
  3. Configure dial peers:
    dial-peer voice 2300090 pots
    destination-pattern 6...
    supplementary-service pass-through
    port 0/2/0:0
    forward-digits all
    dial-peer voice 2300091 pots
    destination-pattern 6...
    supplementary-service pass-through
    port 0/2/0:1
    forward-digits all
    dial-peer voice 2300092 pots
    destination-pattern 6...
    supplementary-service pass-through
    port 0/2/0:2
    forward-digits all
    dial-peer voice 8800 voip
    service session
    destination-pattern 8800
    voice-class codec 4
    session protocol sipv2
    session target ipv4:192.168.50.137
    dtmf-relay rtp-nte
    supplementary-service pass-through

End

Next Steps


Configuring a T1 CAS environment

Purpose

To configure a T1 CAS environment. This section provides an example of a T1 CAS configuration.

Start

  1. Configure a controller:
    controller T1 1/0/1
    framing sf
    clock source internal
    linecode ami
    ds0-group 0 timeslots 1 type e&m-immediate-start
    ds0-group 1 timeslots 2 type e&m-immediate-start
    ds0-group 2 timeslots 3 type e&m-immediate-start
  2. Configure voice ports:
    voice-port 0/2/0:0
    output attenuation 0
    station-id name 2300090
    voice-port 0/2/0:1
    output attenuation 0
    station-id name 2300091
    voice-port 0/2/0:2
    output attenuation 0
    station-id name 2300092
  3. Configure dial peers:
    dial-peer voice 2300090 pots
    destination-pattern 6...
    supplementary-service pass-through
    port 0/2/0:0
    forward-digits all
    dial-peer voice 2300091 pots
    destination-pattern 6...
    supplementary-service pass-through
    port 0/2/0:1
    forward-digits all
    dial-peer voice 2300092 pots
    destination-pattern 6...
    supplementary-service pass-through
    port 0/2/0:2
    forward-digits all
    dial-peer voice 8800 voip
    service session
    destination-pattern 8800
    voice-class codec 4
    session protocol sipv2
    session target ipv4:192.168.50.137
    dtmf-relay rtp-nte
    supplementary-service pass-through

End

Next Steps


Configuring a T1 PRI environment

Purpose

To configure a T1 PRI environment. This section provides an example of a T1 PRI configuration.

Start

  1. Configure a controller:
    controller T1 0/0/0
    framing esf
    linecode b8zs
    pri-group timeslots 1-24
  2. Configure an interface serial:
    interface Serial0/0/0:23
    no ip address
    encapsulation hdlc
    isdn switch-type primary-ni
    isdn incoming-voice voice
    no cdp enable
  3. Configure a voice port:
    voice-port 0/0/0:23
  4. Configuring dial peers:
    dial-peer voice 9 pots
    destination-pattern 9T
    incoming called-number 9...
    port 0/0/0:23
    dial-peer voice 8800 voip
    service session
    destination-pattern 8800
    voice-class codec 4
    session protocol sipv2
    session target ipv4:192.168.50.137
    dtmf-relay rtp-nte
    supplementary-service pass-through

End

Next Steps


Configuring an E1 PRI environment

Purpose

To configure an E1 PRI environment. This section provides an example of an E1 PRI configuration.

Start

  1. Configure a controller:
    controller E1 0/2/1
    framing NO-CRC4
    pri-group timeslots 1-31
  2. Configure an interface serial:
    interface Serial0/2/1:15
    no ip address
    encapsulation hdlc
    isdn switch-type primary-net5
    isdn protocol-emulate network
    isdn incoming-voice voice
    no cdp enable
  3. Configure a voice port:
    voice-port 0/2/1:15
  4. Configure dial peers:
    dial-peer voice 130 pots
    destination-pattern 130T
    direct-inward-dial
    port 0/2/1:15
    dial-peer voice 8800 voip
    service session
    destination-pattern 8800
    voice-class codec 4
    session protocol sipv2
    session target ipv4:192.168.50.137
    dtmf-relay rtp-nte
    supplementary-service pass-through

End

Next Steps


Configuring a SIP User Agent

Purpose

To configure a SIP User Agent. This section provides an example of a SIP User Agent configuration.

Start

Configure a SIP User Agent: enter global configuration "configure terminal":
sip-ua
timers notify 400
sip-server dns:host.genesyslab.com

End



This page was last modified on July 16, 2013, at 16:35.

Feedback

Comment on this article:

blog comments powered by Disqus